If a GFCI outlet keeps tripping, the cause is usually one of five things: moisture, a faulty appliance or cord, too many devices on one GFCI, a wiring problem on the circuit, or a GFCI that is wearing out. A GFCI (ground fault circuit interrupter) compares the current going out on the hot wire with the current coming back on the neutral. If some of it goes missing, it cuts the power. The U.S. Consumer Product Safety Commission says a GFCI reacts to a difference as small as 0.006 amps (6 milliamps) and shuts the power off almost instantly (CPSC GFCI fact sheet).
So a trip means the GFCI is doing its job. This guide covers the common causes, how to reset a GFCI outlet, why some will not reset, how to tell if one is bad, and when to call an electrician.

What a GFCI Does and Where You Will Find One
CPSC describes three types: the GFCI receptacle (the outlet with TEST and RESET buttons), the GFCI circuit breaker, and portable GFCIs. A GFCI receptacle can also protect ordinary outlets wired after it on the same circuit, so a dead bathroom or patio outlet is sometimes fixed by pressing RESET on a GFCI in another spot. Check nearby bathrooms, the kitchen, the garage and outdoor outlets, then the breaker panel. Our guide on what to do when an outlet stops working covers that search.
The Electrical Safety Foundation lists kitchens, bathrooms, garages, laundry areas, basements and crawlspaces, outdoor areas, and outlets near sinks, spas and hot tubs (ESFI, How to Use GFCIs). CPSC notes that code requirements were added over time, for example outdoor outlets in 1973, bathrooms in 1975, garages in 1978 and kitchens in 1987. An older Abilene home may have GFCIs in some of these places and not others.
What Causes a GFCI to Trip?
- Moisture. Water in an outdoor box, a damp garage or bathroom splashes can create a small leak to ground. An engineering review by Henderson Engineers lists moisture and outdoor locations among the causes of repeated tripping and suggests weatherproof covers (Henderson Engineers).
- A faulty appliance or cord. A worn cord or an appliance with damaged insulation can leak current to ground. Then the fix is the appliance, not the outlet.
- Too many things on one GFCI. Henderson Engineers notes that listed appliances can each leak a tiny amount of current (up to 0.75 milliamps), and several on the same GFCI can add up to a trip.
- Very long circuits. The same review links long wire runs to extra leakage. This can matter on a long feed to a detached shop or barn.
- A wiring problem. A damaged wire, a loose connection, or a neutral that is shared or connected wrong can make a GFCI trip with nothing plugged in.
- A worn or damaged GFCI. GFCIs can fail, and CPSC notes that blackouts and power disturbances can damage a GFCI’s ability to work.
Why Your GFCI Outlet Keeps Tripping: What It Means and What to Do
| What you notice | What it usually means | What to do |
|---|---|---|
| It trips only when one appliance runs | That appliance or its cord is leaking current | Try the appliance on a different GFCI outlet. If it trips there too, have the appliance repaired or replaced. |
| An outdoor GFCI trips after rain or sprinklers | Water got into the outlet, the cover or a cord connection | Let it dry before you reset it and keep the cover closed. If it keeps happening, have the outlet and box checked. |
| It trips with nothing plugged in | A wiring fault or moisture somewhere on the circuit, or a failing GFCI | Stop resetting it and call an electrician. |
| It trips again right after you reset it | The fault is still there | Unplug everything on it and the outlets after it. If it still trips, the wiring or the GFCI is at fault. |
| It will not reset and no light is on | No power is reaching it, or it is wired wrong | Check the breaker panel. If the breaker is on and it still will not reset, call an electrician. |
| A red status light stays on or keeps flashing | The GFCI may have a problem | Follow the maker’s instructions. A short red flash right after a reset can be normal on some models. If it cannot be reset, it must be replaced. |
How to Reset a GFCI Outlet
- Unplug everything from the GFCI and the outlets it protects.
- Make sure the outlet and your hands are dry. Do not reset an outlet that is wet, cracked, scorched or smells hot.
- Press RESET firmly until it clicks and stays in. A lamp plugged into the outlet, or the status light if your GFCI has one, will show that power is back.
- Test it. CPSC’s method is simple: plug in a lamp and turn it on, press TEST, and the lamp should go off. Press RESET and the lamp should come back on.
- Plug things back in one at a time. If the GFCI trips when one device goes back in, you have found the likely cause.
If RESET will not stay in, do not force it or hold it down.
GFCI Outlet Won’t Reset? Common Reasons
- No power is reaching it. Leviton’s instructions for its GFCI receptacles explain that they cannot be reset when no power is supplied. Check the breaker panel first. Our guide to why a breaker keeps tripping can help if the breaker trips again.
- Another GFCI upstream has tripped. If this outlet is downstream of a GFCI in another room, reset that one first.
- The fault is still there. A wet box or a damaged wire will keep it from resetting.
- It was wired backward. GFCIs have LINE terminals (incoming power) and LOAD terminals (outlets after it). Leviton states that if the incoming wires are connected to the LOAD terminals, the GFCI will not reset and will not provide power (Leviton GFCI instruction sheet).
- It has reached the end of its life. UL’s GFCI standard has required self-testing on GFCIs made since June 29, 2015, and in most cases those units are designed to cut power when they reach end of life (IAEI Magazine, UL Question Corner). A newer GFCI that will not reset may simply be worn out and need replacing.

How to Tell If a GFCI Outlet Is Bad
Start with the test button. CPSC recommends testing every GFCI after it is installed, at least once a month, and after a power failure. Leviton’s instructions also say to press TEST, then RESET, every month. A GFCI is bad if:
- Pressing TEST does not cut the power. CPSC says that means the GFCI is not working or was installed wrong, and a qualified electrician should correct the wiring or replace it.
- Pressing RESET does not bring power back. CPSC and ESFI both say to replace it.
- A red status light stays on or keeps flashing. Leviton says a solid or flashing red light means a problem may exist.
- The outlet feels warm, looks discolored or buzzes. See is it dangerous if a plug gets warm.
Self-testing GFCIs do not replace the TEST button. IAEI Magazine explains that the automatic self-test cannot check every part, such as the trip mechanism and the contacts, so manual testing is still recommended.
How Long Do GFCI Outlets Last?
There is no fixed number. InterNACHI’s life expectancy chart lists GFCIs at up to 30 years but notes they can last much less if they trip often (InterNACHI). Treat the monthly test as your answer: if a GFCI fails the test, replace it, no matter how old it is. After a storm outage, test your GFCIs as part of the cleanup. Our power outage and storm electrical safety checklist covers the other things to check.
A Texas Note: GFCIs and Outdoor AC Units
Texas adopted the 2026 National Electrical Code as the state electrical code, effective September 1, 2026, with a limited exception for GFCI protection on certain outdoor outlets (TDLR). TDLR’s announcement describes that exception as an amendment to section 210.8(F) so that GFCI protection is not required on outdoor HVAC outlets at homes (TDLR, The Texas Circuit, July 2026). The rule proposal pointed to unresolved concerns about GFCI devices and HVAC equipment causing nuisance tripping and air conditioning outages (Texas Register, March 2026).
If your outdoor AC unit or heat pump keeps shutting off and it is on a GFCI, do not bypass or remove the GFCI yourself. Have a licensed electrician find out why it trips and what protection that circuit needs.
When to Call an Electrician
- The GFCI trips with nothing plugged in, or trips again right after a reset with everything unplugged.
- It will not reset and the breaker is on.
- The outlet is warm, discolored, cracked, buzzing, or smells like burning plastic. If you see smoke or flames, get out and call 911. See what an electrical fire smells like.
- A GFCI fails its test, or you want GFCI protection added where you do not have it. CPSC recommends having a qualified electrician install GFCI breakers and receptacles.
Anything behind the outlet cover or inside the panel is work for a licensed electrician. We replace GFCI outlets and track down the cause of repeated trips as part of our outlet and switch repair service, and we add new protected circuits through our electrical installation work.
Frequently Asked Questions
Why does my GFCI keep tripping with nothing plugged in?
That points to a wiring problem, moisture in a box on the circuit, or a failing GFCI. The GFCI may also protect outlets in other rooms, so unplug things there too. If it still trips, have it checked.
Can a bad appliance make a GFCI trip?
Yes. A damaged cord or an appliance with worn insulation can leak current to ground. If the GFCI trips only when that appliance is plugged in, and it trips on other GFCIs too, the appliance is the problem.
Is it dangerous if a GFCI keeps tripping?
The trip itself is the GFCI protecting you. What matters is the cause. A wet outlet or a bad appliance is easy to deal with, but repeated trips with nothing plugged in can mean damaged wiring.
Need a GFCI Checked or Replaced?
If a GFCI keeps tripping, will not reset or fails its test, call (325) 326-5306. We offer free estimates and upfront pricing, so you approve the price before work starts. We work in Abilene and the nearby towns, including Dyess AFB, Tye, Merkel, Clyde, Potosi, Buffalo Gap and Tuscola. For anything urgent, see our emergency electrician page.
