How to Reset a Breaker Safely (and When Not To)

How to Reset a Breaker Safely (and When Not To)

Knowing how to reset a breaker can get the lights back on in a minute when a circuit shuts off. The short answer: switch off or unplug what was running on that circuit, find the breaker whose handle sits in the middle or shows a colored flag, push the handle firmly all the way to OFF, then push it back to ON. If it trips again right away, stop there. The Siemens breaker diagnostic guide puts it plainly: if the breaker trips again, “a fault still exists on the circuit,” and that is a job for an electrician.

A tripped breaker is not a broken breaker. It shut the power off because it sensed too much current or a fault, which is its job. If the same breaker trips over and over, our guide on why a breaker keeps tripping explains the usual causes.

Hand unplugging a power cord from a wall outlet before resetting a breaker

Before You Reset: Quick Safety Checks

Do not reset the breaker, and call an electrician instead, if you notice any of these:

  • A burning or hot plastic smell, smoke, or scorch marks on the panel, an outlet or a switch.
  • A panel or breaker that feels hot, or buzzing or crackling coming from the panel.
  • Water on or near the panel, or a wet floor where you would stand. After a flood, Schneider Electric advises not to enter a building with standing water until you are sure the main power is off, to have an electrician or the utility shut it off, and to replace electrical equipment that has been underwater.
  • A spark, flash or pop at an outlet or appliance when the breaker tripped.

If you see smoke or flames, get everyone out and call 911.

When it is safe to go ahead, dry your hands, stand on a dry surface and bring a flashlight. The reset instructions from Southern California Edison (SCE) add two habits: use only one hand, and stand to the side of the panel in case the breaker arcs. Only open the outer door. The inner cover that hides the wiring stays on; anything behind it is work for a licensed electrician.

How to Tell If a Breaker Is Tripped

Breaker panels are often in a garage, utility room, hallway or closet, or on an outside wall. Open the door and look along the rows of handles:

  • Look for a handle in the middle. SCE describes a tripped breaker as sitting in the off position or partway between on and off. On Square D QO breakers, Schneider Electric says the tripped handle sits about midway. Look for the one handle that does not line up with the rest.
  • Look for a flag. Some breakers show a colored flag in a small window when they trip. QO breakers show a red flag, and SCE says a tripped breaker usually shows an orange flag.
  • Check the labels. The directory on the panel door should list which breaker feeds which room. If yours is blank or out of date, it is worth updating once the power is back.

Every breaker is on, but an outlet is dead? Look for a GFCI outlet with a tripped RESET button, often in a bathroom, kitchen, garage or outside. See our guide to a GFCI outlet that keeps tripping, or what to do when an outlet stops working.

The whole house is dark and nothing tripped? Check whether your neighbors have power. AEP Texas takes outage reports at 1-866-223-8508 and online. Taylor Electric Cooperative members can call (325) 793-8500 or use the co-op’s app. Our power outage electrical safety checklist covers what to unplug while you wait.

How to Reset a Breaker in 5 Steps

  1. Turn things off on that circuit. Switch off the lights and unplug appliances in the rooms that lost power. SCE lists this as the first step, so the circuit is not loaded the moment power comes back.
  2. Find the tripped breaker. Look for the handle in the middle or a colored flag, as described above.
  3. Push the handle all the way to OFF. This is the step that resets the breaker. Schneider Electric explains that a tripped breaker has to be moved from the tripped position to OFF before it can be turned back on, and that this takes some force because springs inside are being compressed. Skip it and the breaker may not stay on.
  4. Push it back to ON. Use one hand and stand to the side. The handle should stay firmly in the ON position, lined up with the others.
  5. Turn things back on one at a time. If the breaker trips again as soon as a certain appliance starts, that appliance, or the total load on the circuit, is the likely cause. Move it to another circuit if you can.

One reset is reasonable. Resetting again and again is not: SCE advises resetting a breaker that trips repeatedly only once the problem has been corrected. The causes it lists include too many devices on one circuit, a damaged cord or plug, a short in an outlet, switch or fixture, and faulty wiring.

What you noticeWhat it likely meansWhat to do
It trips again right away, even with everything unpluggedA fault still exists on the circuit (Siemens)Leave it off and call an electrician
It trips when one appliance starts or runsToo much load on the circuit, or a fault in that applianceUse a different circuit and see why a breaker keeps tripping
The handle will not stay onIt was not pushed fully to OFF first, or the breaker may be failingTry once more, all the way to OFF, then ON. If it still will not hold, call an electrician
The breaker or panel feels warm, buzzes or smells hotSomething is overheatingDo not reset it. Call an electrician. Smoke or flames: call 911
The whole house is out and nothing looks trippedA utility outage, or the main breakerCheck with your neighbors and your utility, then see the main breaker section below
One outlet is dead and every breaker is onA tripped GFCI outlet upstreamFind the GFCI outlet and press RESET

Resetting AFCI and GFCI Breakers

Many newer panels include AFCI breakers, which watch for dangerous arcing, and GFCI breakers, which watch for current leaking to ground. You can spot them by the TEST button on the front. When they trip, the handle moves to the middle tripped position like a standard breaker (Schneider Electric says this of its GFI breakers), and you reset them the same way: OFF, then ON.

Some of these breakers record why they tripped. Siemens’ guide says to observe and record the trip indicator lights, because the pattern shows the last trip condition, such as an overcurrent, an arc fault or a ground fault. If yours has indicator lights, take a photo before you reset it and show it to your electrician.

Test AFCIs every month. The Electrical Safety Foundation International (ESFI) recommends a monthly test: with the breaker ON, press TEST. It should trip. Turn it OFF and then ON to reset it. If it does not trip, ESFI says to have a licensed electrician replace it.

The Main Breaker and Older Fuse Boxes

The main breaker is the large breaker, usually labeled MAIN, that controls power to the whole house. If the whole house is dark, your neighbors have power and the main breaker is in the tripped position, turn the air conditioner off at the thermostat and switch off other large appliances, then reset the main the same way: all the way to OFF, then ON. If it trips again, leave it off and call an electrician.

Some older homes still have fuses instead of breakers. A blown fuse cannot be reset. It has to be replaced, and SCE says to use a fuse of the same amperage, so never swap in a bigger one to stop it from blowing. If your home still runs on fuses, our guide to types of wiring in old houses explains what else to check, and an electrical panel upgrade may be worth a conversation.

When to Stop Resetting and Call an Electrician

The National Fire Protection Association’s electrical safety tip sheet says to call a qualified electrician if you have frequent problems with blowing fuses or tripping circuit breakers, discolored or warm wall outlets, a burning or rubbery smell from an appliance, flickering or dimming lights, or sparks from an outlet.

Also call if a breaker will not stay on after a full OFF and ON reset, or if a breaker or the panel feels hot. Our guide on how to tell if a circuit breaker is bad covers the signs of a failing breaker. If a circuit trips whenever a big load runs, such as a space heater, the house may need a new circuit.

We take 24/7 emergency calls. Our licensed electricians work under a Texas electrical contractor license, and with upfront pricing you approve the price before any work starts.

Old home breaker panel with the cover removed, showing breakers and wiring

Frequently Asked Questions

How do I know which breaker is tripped?

Look for the handle that sits in the middle or at OFF instead of lining up with the others, or a red or orange flag in a small window. The labels on the panel door show which room each breaker feeds.

Why won’t my breaker reset?

First check that you pushed the handle all the way to OFF before pushing it to ON; a tripped breaker has to be reset at OFF, and it can take some force. If it still will not stay on, or trips the moment you turn it on, there is likely a fault on the circuit or a problem with the breaker. Leave it off and call an electrician.

How many times can you reset a breaker?

Once, after you unplug what was running. If it trips again, stop and find the cause first, or call an electrician.

Is it safe to reset a breaker yourself?

Yes, if your hands and the floor are dry, there is no burning smell, heat or water near the panel, and you only touch the breaker handle. Never remove the inner panel cover.

Does a tripped breaker mean the breaker is bad?

No. Tripping is the breaker’s job. A breaker that will not stay reset, feels hot, or trips with very little running may be failing, which is a different problem. See how to tell if a circuit breaker is bad.

Need Help With a Breaker in Abilene?

If a breaker will not reset, keeps tripping or smells hot, call (325) 326-5306 or use our contact page. We offer free estimates and work in Abilene and the nearby towns, including Dyess AFB, Tye, Merkel, Clyde, Potosi, Buffalo Gap and Tuscola.

author avatar
Electrician Abilene Licensed Electrical Professionals
The Electrician Abilene Team shares trusted electrical advice, practical safety tips, and expert guidance to help homeowners and businesses make informed electrical decisions throughout Abilene, TX.
Electrician Abilene Tx Logo